National Electrical Code (NEC) Article 225 Practice Exam

These questions are part of the practice quiz. Start practicing

• What is the minimum vertical clearance required for overhead conductors above the roof surface?
• What is a requirement for installing isolating switches on the supply side of a disconnecting means?
• What factors determine the type of insulation required for conductors exposed to outdoor conditions?
• What is the minimum separation required between conductors supported on poles?
• What does the electrical system design need to include before installation testing?
• Is it permissible to run multiple separate branch circuits in the same raceway for outdoor installations?
• What types of devices can be used as disconnecting means according to the NEC?
• How far above public streets must overhead conductors maintain clearance when subjected to truck traffic?
• In terms of safety and compliance, why is clearance critical in electrification over buildings?
• According to the NEC, what is one of the requirements for disconnect construction?
• How does Article 225 address the routing of underground cable in relation to paving?
• What does the up position signify for vertically operated disconnecting means?
• What type of circuit is considered a single circuit for the purpose of feeder regulations?
• Which of the following materials is NOT suitable for supporting open conductors?
• What is the minimum ampacity requirement for the neutral conductor in outdoor lighting circuits?
• What is the required increase in clearance for voltages above 22 kV according to NEC guidelines?
• Which type of wiring installation is permitted on the surfaces of buildings for circuits not exceeding 1000 volts?
• Which of the following describes temporary service installations?
• What is the required lateral clearance from nonbuilding structures like antennas?
• What spacing applies to conductors on poles installed without racks or brackets?
• Which of the following is a requirement for raceways on the exterior surfaces of buildings?
• When considering clearances over roadways, what factors are primarily assessed?
• What is the maximum supply voltage for which additional feeders may be permitted due to capacity requirements?
• What type of connectors are permissible for attaching grounded conductors at the disconnecting means?
• Which of the following types of wiring is suitable for installation on the surfaces of buildings?
• How do markings on service equipment enhance safety when installing outdoor circuits?
• Are there special provisions for installation in agricultural areas within Article 225?
• What is the primary purpose of a disconnecting means in electrical systems?
• How many disconnects are allowed per supply as per the NEC requirements?
• What is necessary for instrument transformers before they are put into service?
• What is required regarding the adjustment of protective circuits?
• What is required to be delivered to the authority having jurisdiction before energization?
• Where should lamps for outdoor lighting be located in relation to energized conductors?
• What is the minimum horizontal clearance required for final spans from windows designed to be opened?
• What is the maximum length for a feeder run indicated in Article 225?
• Clearances above what voltage require a specific increase according to NEC standards?
• What distance should conductors be kept from the edges of doors and similar openings?
• Which type of cable is NOT typically allowed for outside installations on buildings?
• What is the required location for the disconnecting means in relation to the building or structure served?
• What is the minimum height for overhead service conductors above a residential driveway?
• How many feeders or branch circuits are allowed to supply a building served by a service disconnecting means?
• Which document is referenced for additional acceptance testing specifications?
• Which type of conductors is required to be insulated when within 3.0 m of a building or structure?
• What feature must single-pole units on multiwire circuits have to be considered as one multipole disconnect?
• Is it permissible to run non-metallic sheathed cable as an outside branch circuit?
• What must clearances over buildings and structures be compared to, as per the guidelines?
• What is the purpose of handler ties in disconnects for multiwire circuits?
• Which conductors are not permitted in outdoor installations?
• Can exterior systems and circuits be interconnected with interior circuits?
• What must each disconnect in a grouping be marked with?
• Which of the following types of conduit is NOT permitted for outside wiring installations on buildings?
• What does Article 225.3 address in relation to conductors and equipment?
• Are temporary service installations covered under Article 225?
• Which of the following clearances is required horizontally from overhead conductors?
• What must be assessed when running multiple conductors in a conduit?
• What is a common requirement for conduit used in outdoor installations?
• What type of testing is specified for metering circuits to ensure proper functionality?
• For areas with voltage exceeding 300 volts, what is the required clearance over residential property?
• What is the key requirement for the rating of disconnects according to NEC standards?
• Where conductors run above the top level of a window, what is the requirement related to the 900 mm (3 ft) rule?
• What must be done to the disconnecting means according to NEC requirements?
• Which type of wire insulation is mentioned for festoon lighting compliance with NEC?
• What is required for a building or structure disconnecting means according to NEC standards?
• Are flexible cords acceptable for power supply over temporary outdoor stages?
• What must be provided if the disconnecting means does not disconnect the grounded conductor?
• According to the NEC, what is the minimum size of copper conductors for spans up to 15 m when the nominal voltage is 1000 volts or less?
• What is required when mounting service equipment outdoors?
• What section of Article 225 addresses the installation of service-entrance conductors?
• What are branch circuits?
• What is the minimum working space required in front of a disconnecting means?
• How should a mast be supported to ensure it withstands the strain of overhead conductors?
• What should be done with outside branch-circuit conductors passing over a building?
• What is the required vertical clearance for final spans above platforms or surfaces preventing personal contact?
• Additional feeders for different voltages are permitted under what condition?
• Which section specifies requirements for outside branch circuits and conductors?
• Final spans of feeders or branch circuits must comply with which requirement?
• What is the minimum rating for a branch circuit disconnecting means supplying a single branch circuit?
• For special conditions, additional feeders or branch circuits may be permitted for:
• What is the minimum separation distance for open conductors of 1000 volts, nominal or less?
• What is the key takeaway from Article 225 about safety around outdoor electrical installations?
• How are service-entrance conductors protected?
• What type of connection must be used for outdoor lampholders attached as pendants?
• For circuits up to 277 volts, what is the intended application of such circuits according to the NEC?
• What should NOT be done when attaching conductors to a mast?
• What does Article 225 say about bonding and grounding for outdoor circuits?
• According to NEC requirements, what is the minimum number of disconnects required for service?
• What is the purpose of maintaining clearance over buildings and structures?
• What is the incremental clearance specification for conductors above 22 kV nominal to ground?
• What is the minimum clearance distance required from the edge of a roof for overhead conductors?
• What is required for the sizing of conductors over 1000 volts according to the NEC?
• Where should branch-circuit overcurrent devices be installed if the feeder overcurrent device is not readily accessible?
• In situations where overhead conductors are present, what is a critical requirement for their installation?
• What should be taken into account regarding foliage when running outdoor branch circuits?
• What is required for each disconnecting means to serve as service equipment?
• In terms of conductor spacings, what requirement applies to conductors over 1000 volts, nominal?
• Which code provides additional information for clearances above 22 kV?
• What type of conductors should be used for festoon lighting?
• What type of enclosure is typically required for overhead conductors in hazardous areas?
• In a multiple-occupancy building, who has access to the supply disconnecting means?
• How should the "on" and "off" positions of disconnecting means be indicated?
• For electrical installations over 22 kV, which of the following relationships is accurate?
• Are temporary overhead service drops allowed for permanent installations?
• What is the minimum cover required for underground conductors?
• For lighting equipment installed outdoors, which NEC Article must be complied with?
• What is the requirement for disconnecting means in buildings?
• What is the minimum clearance requirement for overhead conductors above finished grade where the voltage does not exceed 150 volts?
• What must happen in the event of a power failure regarding disconnecting means?
• What type of conductor insulation is suitable for outdoor locations in accordance with NEC?
• How should the building or structure disconnecting means indicate its status?
• How should the characteristics of fuses in a switch contribute?
• What must be verified in control or signal circuits according to the current standards?
• How should relays and metering that use phase differences be verified?
• What is the required method to protect overhead conductors in areas subject to physical damage?
• What type of conductor is commonly used for underground service laterals?
• In buildings exceeding a certain height, how far should the clear zone begin from the building?
• What clearance is required for conductors up to 22 kV over roadways according to the standards?
• What type of equipment is typically prohibited from being installed outdoors according to Article 225?
• What is required where a raceway enters a building from the outside?
• Which of the following is NOT a factor affecting clearance requirements as per NEC Article 225?
• What materials can be used to support open conductors?
• What is the primary focus of Article 225 in the National Electrical Code?
• What should be avoided as support for overhead conductor spans?
• What is indicated for spans supported by messenger wires according to NEC regulations?
• What conductor size is not permitted for open individual conductors over 1000 volts?
• Which of the following may be a condition under which documented switching procedures must be established?
• When conductors are supported on poles, what is the minimum separation required between them?
• Can underground service conductors cross under a driveway unprotected?
• What markings are required on outdoor service equipment?
• What type of circuits must be observed to perform their proper control function?
• What is the maximum number of feeders allowed from the same panelboard if each terminates in a single disconnecting means?
• What must be done to conductors that are run underground according to Article 225?
• What is an important requirement for raceways used in wet locations?
• What does testing switching circuits ensure?
• What is the minimum width of a clear zone for fire ladders needed when buildings exceed certain heights?
• For how many instances does Article 225 specify that multiple disconnecting means can be used for outside feeders?
• How does Article 225 primarily handle underground service installations?
• What marking must indicate the operation of disconnects for outdoor feeders?
• How often should outdoor disconnect switches be inspected?
• What type of installation requires a feeder disconnect rating of at least 100 amperes?
• What additional requirements apply to service equipment located in hazardous locations?
• What is one of the purposes of the feeder or branch-circuit disconnecting means?
• According to the NEC, how should disconnecting means be marked?
• What is the purpose of complete acceptance tests after substation installation?
• Which of the following is NOT a requirement for outside branch circuits?
• Where should conductors not be attached on a mast?
• What must be provided for multiconductor cables on exterior surfaces?
• What happens if the clearance requirements are not met as per NEC regulations?
• What does the presence of phase angles in relays indicate?
• What is required for all locations where feeders and branch circuits exist within a building?
• When can additional feeders be allowed due to capacity requirements?
• In outdoor electrical installations, which conductors require compliance with NEC standards?
• What requirement must be met at the point of attachment of conductors to a building?
• What limitation does Article 225 impose on the use of extension cords for outdoor purposes?
• What is a critical installation consideration for overhead service drops near swimming pools?
• How much should clearances be increased for every 1 kV above 22 kV?
• Who is responsible for ensuring compliance with clearance requirements in an electrical installation?
• What general safety precautions should be taken when working with outdoor circuits?
• What is a requirement for feeder and branch-circuit conductors entering a building?
• How many conductors can be run in a conduit for a branch circuit?
• What is the purpose of Article 225 in the NEC?
• What is the significance of referencing other NEC articles within Article 225?
• What is a common violation related to the installation of feeders covered in Article 225?
• Which of the following is true regarding the requirements found in NEC Article 225?
• What is a key requirement for the location of disconnecting means for outside feeders?
• How does Article 225 dictate the routing of feeders in residential installations?
• What is necessary for outdoor lampholders to ensure safety when making connections?
• Where should additional disconnecting means for fire pumps be placed?
• When is the use of cable assemblies instead of conductors permitted?
• What is one of the required characteristics for sealants used where a raceway enters a building?
• Which of the following describes the Informational Note included in the clearance requirements?
• In special cases involving crossings over lakes or rivers, what is required for clearance designs?
• Which of the following is NOT part of the acceptance tests required for substations?
• Which of the following is an exception to the maximum number of disconnects rule?
• How should all feeder disconnects supplying the same building or structure be arranged?
• What is the NEC's guideline regarding the height of service drops over roofs?
• What is the maximum allowable voltage drop for feeder circuits as per NEC recommendations?
• What is the minimum rating for disconnecting means in all other installations not covered by specific cases?
• What type of enclosures are required for disconnects in outdoor installations?
• When determining clearance, which of the following factors must be considered for conductors not over 1000 volts?
• What is the required support for overhead conductors exceeding 12 m in spans for festoon lighting?
• When installing overhead branch-circuit conductors, where must they not obstruct?
• For disconnects used for fire protection and water pumps, what is an exception regarding their location?
• In the case of a multisection switchboard, what is allowed for the grounded conductor disconnect?
• What is the purpose of marking outdoor service equipment?
• What must be marked on each disconnecting means that supplies a building or structure?
• What is a potential hazard that Article 225 addresses regarding outside installations?
• In which scenario can additional feeders be used in multiple-occupancy buildings?
• Which conductors are permitted to be attached to a feeder and/or branch-circuit mast?
• For installations with not more than two 2-wire branch circuits, what is the minimum rating for the disconnecting means?
• When planning installations, what clearance requirements should be consulted for safety?
• What is necessary for buildings with multiple feeders or branch circuits?
• How should metering circuits operate according to the current guidelines?
• What nominal voltage level initiates the additional clearance requirement in NEC Article 225?
• What is the minimum size for conductors used in overhead service drops?
• What is the required means of attachment for conductors to a building according to the code?
• What is the minimum fault-closing rating required for a building disconnect?
• What is required for conductors installed on buildings to ensure protection against physical damage?
• Which of the following best describes the function of Table 225.61 in the NEC?
• Which of the following is NOT a condition where additional feeders or branch circuits may be permitted?
• According to Article 225, what must protective devices in outdoor circuits be rated for?
• What characteristic is NOT a requirement for building or structure disconnecting means?
• What is the minimum required climbing space for power conductors below communications conductors?
• What does Article 225 of the National Electrical Code cover?
• Which of the following describes the requirement for conductors in overhead service drops?
• What is the required minimum rating for feeder disconnecting means in a one-family dwelling?
• What is the maximum allowable voltage to ground for circuits supplying outdoor luminaires in commercial areas?
• What are the two main types of service drop configurations mentioned in Article 225?
• What is NOT a method of testing protective relays as per NEC guidelines?
• What is the minimum rating for a feeder disconnecting means according to NEC?